Let’s discuss microplastics in the environment, or more specifically, microplastic potential from civil engineering products made from plastic, which we call polymer-based products or polymeric products.
Microplastics come from a wide range of products. We use polymer-based products in our daily life all the time. This includes but is not limited to clothing, household items, stationery, packaging, even personal hygiene items such as masks and gloves. These all have the potential to cause microplastics, but we want to look specifically at polymer-based, civil engineering products.
The definition of microplastics is not always clear. Most people agree that it’s particles of plastic smaller than 5mm, but larger than one micron. Anything smaller than that, we would call nano-plastics.
If we consider where these microplastics come from, we get primary and secondary microplastics.
- Primary microplastics are those that are designed and produced in that small size for their intended application. So that doesn’t really apply to the products we’re talking about today.
- Secondary microplastics are caused by the breakdown of larger items. And this is where we’re going to examine how microplastics relate to civil engineering products.
The types of civil engineering products we’re talking about are:
These are all designed and engineered to be used in civil engineering and infrastructure development, but the question is – do these products put microplastics into the receiving environment?
We believe not, so let’s go into a little more detail.
Primarily, polymer-based products have two ways they can degrade.
1. Physical abrasion. This is when, in the natural environment, they rub against something which causes small pieces of plastic to break off.
2. Chemical or UV degradation. That is when the product degrades within itself, with nothing else touching it, to the point where small pieces fall off.
We can further classify these products, often called geosynthetics, into below ground use and above ground use.
Below Ground Use:
The majority of these products are used below the ground. Geogrids and the engineering fabrics are almost always used below ground. This means that, apart from a very small amount of abrasion when they are first installed, which they are designed to withstand, there will be no further abrasion over their design life.
The design life of these products is very long, usually more than 100 years with no physical abrasion. At the end of that design life, they can be recycled. They are environmentally friendly products, especially when we consider what they’re replacing. Drainage composite, for example, is only about 200-300g of polymer per square meter. It can replace hundreds of kgs of quarried rock traditionally used for drainage, but focusing on our topic today, we can prevent geogrids and fabrics from generating microplastics by engineering them for a hundred-year design life and putting them in an application where there is no abrasion or exposure to UV light.
Other forms of chemical degradation, and hydrolysis and oxidation which are applicable to polyester and polypropylene fibres respectively, are also controlled when they are buried and out of the environment as regards sunshine and rain.
Any hydrolysis or oxidation that may occur is considered in design and addressed with either polymer additives or appropriate reduction factors to ensure the product does not degrade to the point of breakdown. Very few polymer products have this level of long term design consideration.
This means we’re not getting breakdown causing microplastics from either abrasion or chemical degradation when they’re placed underground.
Above Ground Use:
It’s a slightly different story if we put these products above the ground. The two places we generally see these products above the ground are:
1. Geotextiles used for temporary erosion protection on construction sites.
- Once exposed, these products normally have an intended design life of between six months and two years.
- If we put a product that’s designed to be buried above the ground, we are at risk of abrasion and UV degradation.
- So, we design the product to be used above ground.
To do this, we do two different things to that product.
- Firstly, we will use a UV protected product.
- Secondly, we will calender the surface. Calendering is when we put a heat roller over the surface to bind those little fibres together, so that they do not break off and flow into the waterway.
Remember. If drainage products designed to be used underground are used on the surface, there is a risk of creating microplastics.
2. Erosion control matting.
- These use biodegradable materials, such as coconut fibre, instead of plastics.
- If coconut fibres break off into the environment, they will completely degrade.
- Some also use a black, UV stabilised polymer-based product as a backing that acts as a soil stabilisation grid.
If the loose fibres on a product like this were actually plastic, then that would be a danger of creating microplastics, so we only use UV stabilised polymer-based carrier layers and biodegradable products above ground for erosion control matting.
We also embed products such as ECC3 and BioCoir into the root zone, not the foliage zone. So, if you’ve got a swale drain protected with erosion control matting, for example, then that will be completely out of the sunlight anyway.
In general, single use plastics are very different to engineered long-term plastics. We produce long-term plastics to last for over 100 years, and we engineer them into a project so they don’t generate microplastics in the environment. Engineered plastics also save vast quantities of other natural resources, such as quarried products, and we can demonstrate significant carbon-friendly benefits from the use of these engineered polymer-based products.
